You guys, I just love this project from Brittany, and I am so honored that she would share it here in a guest post while I’m snuggling my sweet baby girl. Thanks Brittany!
Hi, everyone! I’m really excited to be guest posting on Simply Designing today! My name is Brittany, and I blog about DIY, home, and garden at by Brittany Goldwyn. Today I am sharing a tutorial about how to make a tree stump side table!
This tree stump side table project had been a long time coming. It’s an easy project when it comes down to it, but it took a lot of patience. That’s because you have to wait for your stump to dry completely before you can start working on it, and that can be anywhere from weeks to months depending on when the tree was cut down and what conditions the stump has been sitting in. My process was even longer because my dad accidentally chucked my first stump that I had drying out at their house. He thought I had forgotten about it because it had been drying for so long! (It’s okay dad, I forgive you.) So when my parents recently took down a tree in their backyard, I was all over finding the best stump from the pile to start my tree stump side table project again.
Here was my inspiration from West Elm…with a $249 price tag.
Lovely, but $249? Nah. Not when you just bought a house! Take a look at my version:
Maybe I’m biased, but I actually like mine better! What do you think? I love how mine has a bit deeper of a color and a little bit more shine to it. So let’s chat about what I used and how I did it!
Here’s what you need to make a tree stump side table:
(Affiliate links below!)
- Tree stump or pry bar
- Flat tip screwdriver
- Bleach and water
- 220-grit sandpaper (assorted pack here)
- Minwax Stain in Special Walnut
- Minwax Polyurethane in Semigloss
And here’s how to do it!
Step 1: Find a stump and peel off the bark. My parents had just taken down a tree in their backyard a few weeks before and kept it for firewood. We looked through the pile and picked the most even stump we could find.
Then I used a flat tip screwdriver to peel off the bark. This bark removal process was MUCH easier than what I had to go through when I made my DIY cat tree using real branches. I could not believe how easy this stump was!
(P.S., you can check out a detailed post I did on how to strip and finished tree branches for decor here!)
Step 2: Clean up your stump. Once I’d removed all of the bark, I had to clean it up. There was some mold growing on the stump due to some of the moisture it still had in it, so I wiped it down with a bleach and water mix at a 1:3 ratio to kill everything that was living on this bad boy. Here is pre-bleach:
Step 3: Once it’s clean, it needs to dry! My stump still had quite a bit of drying to do, so we set it in my parents’ basement right next to a dehumidifier to dry out for a few months. You don’t need to use a dehumidifier, but it just helped to speed up the process.
You can still see some of the stains from where the mold was growing, but the mold itself is long gone. Once the stump dried out completely, it lost a few pounds, too. Here’s my dry stump. You can see some of the staining on the side that I ended up making the bottom:
Step 4: Sand and stain your stump! Polish any rough spots using a 220-grit sandpaper. For the stain, you can keep it looking natural and use a light stain or go dark. I decided on something in the middle. Stain your stump just as you would any other piece of wood. (See my full post on how to stain and finish wood here!)
Step 5: Finish it off. To finish my stump, I gave it two generous coats of Minwax Polyurethane in Semigloss. Make sure to sand lightly in between the first and second coat.
And here it is, done!
This was an easy DIY…like I said, it just took a lot of patience waiting for it to dry out! There was some heated discussion in our house about which end it should stand on…I love it this way, but my husband and friend both wanted it flipped. What do you think?
LIKE THIS? PIN IT!